? 2003 fairchild semiconductor corporation ds012138 www.fairchildsemi.com october 1995 revised may 2003 nc7S00 tinylogic ? hs 2-input nand gate nc7S00 tinylogic ? hs 2-input nand gate general description the nc7S00 is a single 2-input high performance cmos nand gate. advanced silicon gate cmos fabrication assures high speed and low power circuit operation over a broad v cc range. esd protection diodes inherently guard both inputs and output with respect to the v cc and gnd rails. three stages of gain between inputs and output assures high noise immunity and reduced sensitivity to input edge rate. features space saving sot23 or sc70 5-lead package ultra small micropak ? leadless package high speed: t pd 3.5 ns typ low quiescent power: i cc < 1 a balanced output drive: 2 ma i ol , ? 2 ma i oh broad v cc operating range: 2v ? 6v balanced propagation delays specified for 3v operation ordering code: logic symbol ieee/iec pin descriptions function table y = ab h = high logic level l = low logic level connection diagrams pin assignments for sc70 and sot23 (top view) pad assignments for micropak (top thru view) tinylogic ? is a registered trademark of fairchild semiconductor corporation. micropak ? is a trademark of fairchild semiconductor corporation. order number package product code package description supplied as number top mark nc7S00m5x ma05b 7S00 5-lead sot23, jedec mo-178, 1.6mm 3k units on tape and reel nc7S00p5x maa05a s00 5-lead sc70, eiaj sc-88a, 1.25mm wide 3k units on tape and reel nc7S00l6x mac06a a3 6-lead micropak, 1.0mm wide 5k units on tape and reel pin names description a, b input y output nc no connect inputs output aby llh lhh hlh hhl
www.fairchildsemi.com 2 nc7S00 absolute maximum ratings (note 1) recommended operating conditions (note 2) note 1: absolute maximum ratings are those values beyond which damage to the device may occur. the databook specifications should be met, with- out exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. fairchild does not recommend operation of circuits outside the databook specifications. note 2: unused inputs must be held high or low. they may not float. dc electrical characteristics supply voltage (v cc ) ? 0.5v to + 7.0v dc input diode current (i ik ) @v in ? 0.5v ? 20 ma @v in v cc + 0.5v + 20 ma dc input voltage (v in ) ? 0.5v to v cc + 0.5v dc output diode current (i ok ) @v out < ? 0.5v ? 20 ma @v out > v cc + 0.5v + 20 ma dc output voltage (v out ) ? 0.5v to v cc + 0.5v dc output source or sink current (i out ) 12.5 ma dc v cc or ground current per output pin (i cc or i gnd ) 25 ma storage temperature (t stg ) ? 65 c to + 150 c junction temperature (t j )150 c lead temperature (t l ); (soldering, 10 seconds) 260 c power dissipation (p d ) @ + 85 c sot23-5 200 mw sc70-5 150 mw supply voltage (v cc )2.0v ? 6.0v input voltage (v in )0v ? v cc output voltage (v out )0v ? v cc operating temperature (t a ) ? 40 c to + 85 c input rise and fall time (t r , t f ) v cc @ 2.0v 0 ? 1000 ns v cc @ 3.0v 0 ? 750 ns v cc @ 4.5v 0 ? 500 ns v cc @ 6.0v 0 ? 400 ns thermal resistance ( ja ) sot23-5 300 c/w sc70-5 425 c/w symbol parameter v cc t a =+ 25 ct a =? 40 cto + 85 c units conditions (v) min typ max min max v ih high level input voltage 2.0 1.50 1.50 v 3.0 - 6.0 0.7 v cc 0.7v cc v il low level input voltage 2.0 0.50 0.50 v 3.0 - 6.0 0.3v cc 0.3 v cc v oh high level output voltage 2.0 1.90 2.0 1.90 v 3.02.903.0 2.90 i oh = ? 20 a 4.54.404.5 4.40 v in = v il 6.05.906.0 5.90 v v in = v il 3.0 2.68 2.85 2.63 i oh = ? 1.3 ma 4.5 4.18 4.35 4.13 i oh = ? 2 ma 6.0 5.68 5.85 5.63 i oh = ? 2.6 ma v ol low level output voltage 2.0 0.0 0.10 0.10 v 3.0 0.0 0.10 0.10 i ol = 20 a 4.5 0.0 0.10 0.10 v in = v ih 6.0 0.0 0.10 0.10 v v in = v ih 3.0 0.1 0.26 0.33 i ol = 1.3 ma 4.5 0.1 0.26 0.33 i ol = 2 ma 6.0 0.1 0.26 0.33 i ol = 2.6 ma i in input leakage current 6.0 0.1 1.0 av in = v cc , gnd i cc quiescent supply current 6.0 1.0 10.0 av in = v cc , gnd
3 www.fairchildsemi.com nc7S00 ac electrical characteristics note 3: c pd is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (i ccd ) at no output loading and operating at 50% duty cycle. (see figure 2.) c pd is related to i ccd dynamic operating current by the expression: i ccd = (c pd ) (v cc ) (f in ) + (i cc static). ac loading and waveforms c l includes load and stray capacitance input prr = 1.0 mhz, t w = 500 ns figure 1. ac test circuit input = ac waveform; prr = variable; duty cycle = 50% figure 2. i ccd test circuit figure 3. ac waveforms symbol parameter v cc t a = + 25 ct a = ? 40 c to + 85 c units conditions figure (v) min typ max min max number t plh , propagation delay 5.0 3.5 15 ns c l = 15 pf figures 1, 3 t phl 2.0 19 100 125 ns c l = 50 pf 3.0 10.5 27 35 4.5 7.5 20 25 6.0 6.5 17 21 t tlh , output transition time 5.0 3.0 10 ns c l = 15 pf figures 1, 3 t thl 2.0 25 125 155 ns c l = 50 pf 3.0 16 35 45 4.5 11 25 31 6.0 9 21 26 c in input capacitance open 2 10 10 pf c pd power dissipation capacitance 5.0 6 pf (note 3) figure 2
www.fairchildsemi.com 4 nc7S00 tape and reel specification tape format for sc70 and sot23 tape dimensions inches (millimeters) package tape number cavity cover tape designator section cavities status status leader (start end) 125 (typ) empty sealed m5x, p5x carrier 3000 filled sealed trailer (hub end) 75 (typ) empty sealed package tape size dim a dim b dim f dim k o dim p1 dim w sc70-5 8 mm 0.093 0.096 0.138 0.004 0.053 0.004 0.157 0.315 0.004 (2.35) (2.45) (3.5 0.10) (1.35 0.10) (4) (8 0.1) sot23-5 8 mm 0.130 0.130 0.138 0.002 0.055 0.004 0.157 0.315 0.012 (3.3) (3.3) (3.5 0.05) (1.4 0.11) (4) (8 0.3)
5 www.fairchildsemi.com nc7S00 tape and reel specification (continued) tape format for micropak reel dimensions inches (millimeters) package tape number cavity cover tape designator section cavities status status leader (start end) 125 (typ) empty sealed l6x carrier 5000 filled sealed trailer (hub end) 75 (typ) empty sealed tape size abcdn w1 w2 w3 8 mm 7.0 0.059 0.512 0.795 2.165 0.331 + 0.059/ ? 0.000 0.567 w1 + 0.078/ ? 0.039 (177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/ ? 0.00) (14.40) (w1 + 2.00/ ? 1.00)
www.fairchildsemi.com 6 nc7S00 physical dimensions inches (millimeters) unless otherwise noted 5-lead sot23, jedec mo-178, 1.6mm package number ma05b
7 www.fairchildsemi.com nc7S00 physical dimensions inches (millimeters) unless otherwise noted (continued) 5-lead sc70, eiaj sc-88a, 1.25mm wide package number maa05a
www.fairchildsemi.com 8 nc7S00 tinylogic ? hs 2-input nand gate physical dimensions inches (millimeters) unless otherwise noted (continued) 6-lead micropak, 1.0mm wide package number mac06a fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and fairchild reserves the right at any time without notice to change said circuitry and specifications. life support policy fairchild?s products are not authorized for use as critical components in life support devices or systems without the express written approval of the president of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be rea- sonably expected to result in a significant injury to the user. 2. a critical component in any component of a life support device or system whose failure to perform can be rea- sonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com
|
